Loading...
Serving Coral Springs, FL and surrounding areas. (754) 318-0064
Old tile, vinyl, or a peeling coating stands between you and the floor you actually want. We strip it down to bare concrete, haul the debris the same day, and leave a flat slab that is ready for whatever comes next.
Concrete floor stripping in Coral Springs means removing an existing floor covering - tile, vinyl, epoxy coating, or adhesive - down to the bare concrete slab underneath. Most jobs for a single room take one full workday and leave you with a flat, clean surface ready for new flooring or a fresh coating. The slab itself stays in place; the goal is to expose clean concrete so whatever comes next bonds correctly.
This is the step most homeowners skip or underestimate when planning a floor replacement - and it is the most common reason new floors fail within a year or two. If you are planning to install a new epoxy floor coating or any other floor system, starting with a properly stripped and prepared slab is what makes the new installation last.
Once the old material is off, we check the slab for moisture - especially important in South Florida homes where humidity works its way into concrete over time. We pair stripping work with concrete grinding and surface preparation when adhesive residue needs to be fully removed and the slab needs to be leveled before the next floor goes down.
If tiles are cracking, chipping, or lifting at the edges in more than one area of a room, the bond between tile and slab has likely failed. In Coral Springs, moisture from the slab works its way up over time and weakens the adhesive underneath. Patching individual tiles rarely fixes the underlying problem - stripping the floor and starting fresh is usually the more cost-effective long-term solution.
If a corner of your vinyl or tile has come up and you notice dark staining, a musty smell, or visible mold on the underside, moisture has been trapped between the floor covering and the slab. South Florida's humidity makes this a common problem in Coral Springs homes, particularly in bathrooms and kitchens. The old flooring needs to come up completely so the slab can dry out and be treated before anything new goes down.
If you are putting down new tile, luxury vinyl, or hardwood-look planks and the existing floor has noticeable bumps, ridges, or uneven spots, the old material needs to come off first. New flooring installed over an uneven surface will flex, crack, or separate at the seams within a year or two. A flat, clean slab is the only reliable starting point for a floor that will last.
If you have an epoxy or painted coating on a garage or utility room floor and it is starting to peel or bubble in patches, the coating has lost its bond with the concrete. Recoating over a failing surface will only delay the problem - the new coat will fail just as fast. Stripping the old coating down to bare concrete and starting fresh is the only way to get a result that holds.
We handle stripping for all common floor types found in Coral Springs homes and businesses - ceramic tile, porcelain, vinyl, carpet, and existing epoxy or painted coatings. For tile jobs, walk-behind floor scrapers remove the field tile and adhesive layer. For larger commercial areas, ride-on equipment covers more ground in less time. The adhesive residue left after tile is removed is the part most contractors rush past - we treat it as a separate step, using grinders to get the slab clean and flat before anything new goes down. This is where we also coordinate with concrete grinding and surface preparation work when the slab needs leveling or profiling after stripping.
After stripping, we walk you through the bare slab and test for moisture - a step that matters more in South Florida than almost anywhere else. If you are planning a new epoxy floor coating or any other finish system, we will tell you exactly what the slab needs before installation can proceed. Debris is hauled the same day so your space is usable again as quickly as possible.
Best for homeowners replacing original tile in kitchens, bathrooms, or living areas who need a clean slab before new flooring goes in.
Suits homes where older resilient flooring or carpet has delaminated or needs to come up before a moisture test and new installation.
Ideal for garages and commercial spaces where a prior coating has failed and the slab needs to be stripped before a new system is applied.
For floors where old mastic or black adhesive remains after tile is removed - grinding it flush ensures the new floor bonds correctly and sits flat.
The overwhelming majority of Coral Springs homes were built between the 1960s and the 1990s on poured concrete slab foundations - there are no basements and very few crawl spaces. That means the floor you are stripping is also the structural base of your home, which makes careful, controlled removal especially important. Many homes built before 1985 still have original terrazzo floors or multiple layers of ceramic tile installed over decades - terrazzo in particular requires specialized grinding equipment and takes considerably longer to strip than standard tile set with adhesive. If your home predates 1985, let us know upfront so we can account for that in the estimate. Homeowners across Margate, FL deal with the same older housing stock and the same slab-foundation conditions we see throughout Coral Springs.
South Florida's year-round humidity rarely drops below 60 percent, and that moisture works its way into concrete slabs over time. When old flooring is stripped away, the slab is exposed - and any trapped moisture can become visible as dampness or white powdery residue. This is the leading cause of new floor failures in the region, which is why we test every slab for moisture before the job is considered complete. Homes in Pompano Beach, FL and the surrounding Broward County area share the same subtropical conditions, and we apply the same slab moisture protocol on every job regardless of neighborhood.
Florida DEP - asbestos regulations for older flooring materials
We respond within one business day. We will ask about the area size, the type of flooring being removed, and whether the home was built before 1980 - that last question helps us flag anything that may need extra attention before the crew arrives.
We come out and look at the floor before giving you a firm number. We check the condition of the existing covering, signs of moisture, and how firmly the old material is bonded to the slab. In homes built before 1980 we may recommend a test to confirm whether older tile or adhesive needs special handling.
On the day of work the crew uses floor scrapers and grinders to remove the existing covering and any adhesive left behind. For a standard room this typically takes one full day; larger areas or floors with heavy adhesive buildup may take two. Dust-containment systems are in place throughout.
Once the old material is off, we clean up debris and haul it away the same day. We walk you through the bare slab, point out anything that needs attention, and test for moisture - giving you a written summary of the slab's condition before we leave so you know exactly what you are working with.
No obligation, no pressure. We come out, look at your floor, and give you a written quote that covers labor, equipment, and debris removal - so you know exactly what you are spending before work begins. Most responses within one business day.
(754) 318-0064South Florida's subtropical humidity is the leading cause of new floor failures in the region, and most contractors skip the moisture test entirely. We test every slab before we leave and give you a written summary - so the floor installation that comes after ours starts from a honest picture of what the slab actually contains.
In Broward County, construction and demolition debris must go to licensed disposal facilities. We haul everything the same day we strip it, and debris removal is included in the written quote - you will not get a surprise line item after the job is done.
Many homes in Coral Springs were built in the 1960s through 1980s with original terrazzo or first-generation ceramic tile that requires specialized equipment and handling. We know what to look for in older properties - including materials that may need testing before we start - and we flag those issues during the estimate, not after work has begun.
We give you a written quote that covers labor, equipment, and debris removal. We do not add line items after the fact unless we find something genuinely unexpected and walk you through it first. In a Coral Springs renovation market where costs have climbed steadily, knowing your number before work begins matters.
A properly stripped slab is the starting point for every floor installation that lasts - and it is the step most contractors rush or skip. Getting it right at this stage saves time, money, and frustration on every floor project that follows.
Install a durable epoxy coating over the clean slab our stripping crew leaves behind.
Learn MoreProfile and level the bare slab after stripping so it is ready for any floor system that follows.
Learn MoreCoral Springs crews fill up fast ahead of busy season - call now or submit the form to lock in your date and get your new floor project moving.